42G3732

Vendor:SOP-24Package Cooled:TID/C:04+

FEATURES • Dual Channel (LH1540) • Current Limit Protection • l/O Isolation, 5300 VRMS • Typical RON 20 Ω • Load Voltage 350 V • Load Current 120 mA • High Surge Capability • Linear, AC/DC Operation • Clean Bounce Free Switching • Low Power Consumption • SMD Lead Available on Tape and Reel

42G3732

Vendor:SOP-24Package Cooled:TID/C:04+

FEATURES • Dual Channel (LH1540) • Current Limit Protection • l/O Isolation, 5300 VRMS • Typical RON 20 Ω • Load Voltage 350 V • Load Current 120 mA • High Surge Capability • Linear, AC/DC Operation • Clean Bounce Free Switching • Low Power Consumption • SMD Lead Available on Tape and Reel

42G3825

Vendor:HARRISPackage Cooled:SMDD/C:08+

The 42G3825 is in the write mode whenever the WE and CE signals are in the active (low) state after address inputs are stable. The latter occurring falling edge of CE or WE will determine the start of the write cycle. The write cycle is terminated by the earlier rising edge of CE or WE . All address inputs must be kept valid throughout the write cycle. WE must return to the high state for a minimum recovery t...

42N03

Vendor:PHPackage Cooled:08+D/C:2000

The V104 10 Bit LVDS Receiver for Video is designed to support video data transmission between display engines and video processing engines for television and projector applications. The V104 supports up to WXGA resolutions for Plasma, Rear Projection, Front Projection, CRT and LCD applications.

42N03

Vendor:PHPackage Cooled:08+D/C:2000

The V104 10 Bit LVDS Receiver for Video is designed to support video data transmission between display engines and video processing engines for television and projector applications. The V104 supports up to WXGA resolutions for Plasma, Rear Projection, Front Projection, CRT and LCD applications.

42N03S

Package Cooled:08+D/C:15000

Most flat-panel monitors and projectors require a digital graphics input in order to accurately scale and display graphics. The huge installed base of computers with analog video graphics interfaces necessitates the use of a graphics digitizer to re- digitize the analog RGB signal before further processing.

42R06-1000G-SIL

42R07-3121-250

42R37-3153-150

42R6959

42S16400(4MX16)

42S18160-60

Vendor:INTEL MITELPackage Cooled:42 SOJD/C:2006

Information Input Concerning Secondary Voltage. By comparing the regulating voltage - obtained from the regulating winding of the transformer - with the internal reference voltage, the output impulse width on pin 15 is adapted to the load of the secondary side (normal, overload, short-circuit, no load).

42S32200-6T

Vendor:ICSID/C:07+

∗ In order to measure at Ta Tj (pulse measurement), fluctuations in output resulting from temperature fluctuations are not included. ∗ Design guaranteed. (Not all products have been inspected.) A capacitor (0.01µF) is used between pin 4 and pin 5, to improve ripple rejection. Not designed for radiation resistance.

42S32200B-7T

Vendor:ISSIPackage Cooled:TSOPD/C:0549+

Port 3 pins P3.0 to P3.5, P3.7 are seven bi-directional I/O pins with internal pull-ups. P3.6 is hard-wired as an input to the output of the on-chip comparator and is not accessible as a general-purpose I/O pin. The Port 3 output buffers can sink 20 mA. When 1s are written to Port 3 pins they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally bei...

42S32200C1-7TL

Vendor:ISSID/C:08+

The HY29F800s sector erase architecture allows any number of array sectors to be erased and re- programmed without affecting the data contents of other sectors. Device erasure is initiated by executing the Erase Command. This initiates an internal algorithm that automatically preprograms the array (if it is not already programmed) before executing the erase operation. During erase cycles, the devic...

42S4210-60-G

Vendor:NECPackage Cooled:SOJD/C:97+

The 16-bit digital output is multiplexed into an 8-bit out- put word that is accessed using two read cycles. The in- ternal registers are programmed through a 3-wire serial interface, which provides gain, offset and operating mode adjustments.

42S4263-80

Vendor:NECPackage Cooled:SOJ

•Built-in digital delay , mixing amplifiers,input output selector achieve a surround system with a single chip . •Delay volume , feedback volume Built-in •ADM digital delay ,16kbit SRAM Built-in •Selection of delay time in a range between 9.2msec and 196.6msec 8 increments. •32 pin SSOP package (32P2U-B) •Built-in automatic reset circuit activated with power on ...

42S51-0H1

Package Cooled:SMD

42TB1/00N

Vendor:eupec

Turn-On Propagation Delay Turn-Off Propagation Delay Turn-On Rise Time Turn-Off Fall Time ITRIP to Output Shutdown Prop. Delay ITRIP Blanking Time ITRIP to FAULT Indication Delay Input Filter Time (All Six Inputs) LIN1,2,3 to FAULT Clear Time Deadtime(IR2130) (IR2132) Operational Amplifier Slew Rate (+) Operational Amplifier Slew Rate (-)

42TL016

42TM003

42V17400ATT-60

Vendor:PANASONISPackage Cooled:30D/C:N/A

42V17400ATT-60

Vendor:PANASONISPackage Cooled:30D/C:N/A

42VF320

Vendor:SST

42Z777

43.008000MHZ

430001351

430002

D/C:2500

4300H1LC

Vendor:CMLD/C:08+

4300H7LC

Vendor:CMLD/C:08+

4301.1403

43018-02

Vendor:MXPackage Cooled:PLCC44D/C:06+

PowerSave (active high). This feature isolates the 2751s data bus interface from the host preventing other bus activities that cause higher power drain during sleep mode. See Sleep Mode with Auto Wake-up and PowerSave Feature section for details.

4301BR-104-181/391

Vendor:BOURNSPackage Cooled:ZIP8PD/C:00+

The Preliminary Information presented herein represents a product in prototyping or pre-production. The noted characteristics are based on initial product characterization. Integrated Circuit Systems, Incorporated (ICS) reserves the right to change any circuitry or specifications without notice. 854058AGwww.icst.com/products/hiperclocks.htmlREV. A APRIL 8, 2004

4301F15/17

Vendor:CMLD/C:08+

4301H1/1

Vendor:CMLD/C:08+

43020-0200

Vendor:MOLEXD/C:07+

Case: JEDEC DO-214BA, molded plastic over glass body Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: AnyWeight: 0.0048 oz, 0.12 g Packaging codes/options: 19/6.5K per 13 Reel (12mm Tape) 17/1.5K per 7 Reel (12mm Tape)

430200400

Vendor:MOLEXD/C:06+

3.3V LVTTL input is a level sensitive strobe used to latch the USB_48/FS_A, FS_B, FS_C/TEST_SEL and PCIF0/ITP_EN inputs. After VTT_PWRGD# (active LOW) assertion, this pin becomes a real-time input for asserting power-down (active HIGH).

43020-0400

Vendor:MOLEXD/C:07+

Circuits for safe protective separation against electri- cal shock according to safety class II (reinforced iso- lation): For appl. class I - IV at mains voltage 300 V For appl. class I - IV at mains voltage 600 V For appl. class I - III at mains voltage 1000 V accord- ing to DIN EN 60747-5-2(VDE0884)/ DIN EN 60747- 5-5 pending, table 2, suitable for: Switch-mode power supplies, line receiver, co...

43020-0401

Vendor:MOLEXD/C:07+

6. Measured with 750 mV (LVPECL) source or 1 V (HSTL) source, 50% duty cycle clock source. All outputs loaded with 50 W to Ground (See Figure 6). 7. Skew is measured between outputs under identical transitions and conditions on any one device. 8. DeviceCtoCDevice skew for identical transitions and conditions. 9. OE Set Up Time is defined with respect to the rising edge of the clock. OE HighCtoCLow trans...

43020-1001

Vendor:MOLEXD/C:07+

Burst mode operation Auto & self refresh capability (8192 Cycles/64ms) LVTTL compatible inputs and outputs Single 3.3V 0.3V power supply MRS cycle with address key programs Latency (Access from column address) Burst length (1, 2, 4 , 8 & Full page) Data scramble (Sequential & Interleave) • All inputs are sampled at the positive going edge of the system clock • Seria...

43021DWR16

Vendor:ONPackage Cooled:SOP-16D/C:02

Reset Logic Output. Pulses low for tRP (Reset Timeout Period) when triggered, and stays low whenever VCC is below the reset threshold or when MR is below VMRT. It remains low for tRP after either VCC rises above the reset threshold, or after MR input rises above VMRT (43021DWR16 only).

43021DWR16

Vendor:ONPackage Cooled:SOP-16D/C:02

Reset Logic Output. Pulses low for tRP (Reset Timeout Period) when triggered, and stays low whenever VCC is below the reset threshold or when MR is below VMRT. It remains low for tRP after either VCC rises above the reset threshold, or after MR input rises above VMRT (43021DWR16 only).

4302-273JTR1000

Fully static operation and Tri-state output TTL compatible inputs and outputs Low power consumption Battery backup(L/LL-part) - 2.0V(min.) data retention • Standard pin configuration - 28 pin 600mil PDIP - 28 pin 330mil SOP - 28 pin 8x13.4 mm TSOP-I (Standard)

43025-0200

Vendor:MOLEXPackage Cooled:08+D/C:78

If an analysis is done of this (which is beyond the scope of this paper) it turns out that this is a much more effec- tive method of reducing the noise than the simple over- sampling and low pass filtering that is outlined above. With a first order filter for H(s) then the SNR improvement that can be realized with Ó∆ techniques is 9dB per octave of oversampling as compared to the 3dB that...

43025-0200

Vendor:MOLEXPackage Cooled:08+D/C:78

If an analysis is done of this (which is beyond the scope of this paper) it turns out that this is a much more effec- tive method of reducing the noise than the simple over- sampling and low pass filtering that is outlined above. With a first order filter for H(s) then the SNR improvement that can be realized with Ó∆ techniques is 9dB per octave of oversampling as compared to the 3dB that...

43025-0400

Vendor:MOLEXD/C:07+

43025-0600

Vendor:MOLEXD/C:07+

Whatever crossover current that might occur in the low-power drivers is dramatically reduced by the series resistor, R4. Additionally, driving the high-power complementary pair using this resistor divider scheme all but eliminates crossover current in this critical output driver. This increases both the drivers efficiency and its reliability.

43025-0800

Vendor:MOLEXD/C:07+

Operate From 1.65 V to 3.6 V Specified From C40C to 85C, C40C to 125C, and C55C to 125C Inputs Accept Voltages to 5.5 V Max tpd of 4.5 ns at 3.3 V Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25C Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25C

43025-0800

Vendor:MOLEXD/C:07+

Operate From 1.65 V to 3.6 V Specified From C40C to 85C, C40C to 125C, and C55C to 125C Inputs Accept Voltages to 5.5 V Max tpd of 4.5 ns at 3.3 V Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25C Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25C

43025-1000

Vendor:MOLEXD/C:07+

The high (VH) and low (VL) terminals of the device are equivalent to the fixed terminals of a mechanical potentiometer. The minimum voltage is C5V and the maximum is +5V. It should be noted that the terminol- ogy of VL and VH references the relative position of the terminal in relation to wiper movement direction selected by the U/D input and not the voltage potential on the terminal.

43025-1200

Vendor:MOLEXD/C:07+

High performance and low cost solution Synchronous operation with high efficiency TTL-compatible 5 bit DAC, output voltage selection from 1.3V to 3.5V programmable High current totem pole output, up to 2 A for direct driving of the external N-Channel power MOSFETs. 200 KHz fixed frequency internal oscillator Fast transient response Power-Good output voltage monitor Over-Voltage and Over-Current protection

430-25-1200-P

430251400

† All typical values are at VCC = 5 V, TA = 25C. ‡ Applies only to the -1 version and only if VCC is between 4.75 V and 5.25 V For I/O ports, the parameters IIH and IIL include the off-state output current. ¶ The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, IOS.

43025-1400

Vendor:MOLEXD/C:07+

The PT4494 is a 20-A Current Booster module designed specifically for the PT4474 programmable DC/DC converter. The booster is controlled directly by the regulator, and effectively adds an additional output stage that operates in parallel. This allows the system to run sychronously, providing a low noise solution. Up to two booster modules can be connected to a PT4474 converter. Each booster module i...

43025-1600

Vendor:MOLEXD/C:07+

Mono-channel multi-level D/A converter High performance analog characteristics • DSD mode (typical values) - THD + N: C109dB (0.00036%) - D.R: 115dB • PCM mode (typical values) - THD+N: C106dB (0.00050%) - D.R: 112dB 2 selectable DSD digital filters PCM input mode • 24-bit, MSB-first, right-justified • 8-times or 4-times oversampling of fs = 16k to 192kHz ...

43025-1800

Vendor:MOLEXD/C:07+

The AD581 can be easily connected with power pnp or power Darlington pnp devices to provide much greater output current capability. The circuit shown in Figure 9 delivers a precision 10 volt output with up to 4 amperes supplied to the load. The 0.1 µF capacitor is required only if the load has a significant capacitive component. If the load is purely resistive, improved high frequency supply rejec...

43025-2000

Vendor:MOLEXD/C:07+

Both 8-pin DIP and SOIC packages are available in the industrial temperature range. The TDFN package has a 4x4mm footprint and features a 0.8mm maximum height. Compared to the 8-pin SOIC the TDFN package footprint is nearly 50% less. For die availability, contact Catalyst Semiconductor marketing.

43025-2400

Vendor:MOLEXD/C:07+

SPI Serial Memory The memory portion of the device is a CMOS Serial EEPROM array with Xicors block lock protection. The array is internally organized as x8 bits. The device fea- tures a Serial Peripheral Interface (SPI) and software protocol allowing operation on a simple four-wire bus.

4302F3-12V

Vendor:CMLD/C:08+

4302F3-5V

Vendor:CMLD/C:08+

All Typical Values are at VCC = 5 V, Ta = 25C The algebraic convention is used in this data sheet for threshold voltage levels only. Not more than one output should be shorted at a time. Refer to EIA standards RS-422A and RS-423A for exact conditions.

43030-0001

Vendor:MOLEX

• Plastic package has Underwriters Laboratories Flammability Classification 94V-0 • Ideally suited for free wheeling diode power factor correction applications • Soft recovery characteristics • Excellent high temperature switching • Optimized to reduce switching losses • High temperature soldering guaranteed: 250C/10 seconds at terminals • Glass passivate...

43030-0002

Vendor:MOLEX

This encapsulated power module can be used in a wide variety of applications, ranging from simple stand-alone operation to an integrated part of a sophisticated power architecture. To preserve maximum flexibility, internal fus- ing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a normal-blow fuse with a maximum rating o...

43030-0003

Vendor:MOLEX

The TMS29F400T/B is a 524 288 by 8-bit / 262 144 by 16-bit (4 194 304-bit), 5-V single-supply, programmable read-only memory device that can be electrically erased and reprogrammed. This device is organized as 512K by 8 bits or 256K by 16 bits, divided into 11 sectors:

43030-0004

Vendor:MOLEX

Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than C0.3V (or 0.3V below the negative power supply, if used)

43030-0005

Vendor:MOLEX

43030-0006

Vendor:MOLEX

Single chip transmit and receive interface for E3, DS3 and STS-1 applications. Interface to 75 ohm coaxial cable over 1100 feet at speeds up to 51.84 Mbps. Compliant with ANSI T1.102-1993, Telcordia GR-499-CORE and GR-253-CORE, ITU-T G.703 and G.823 for jitter tolerance. Compliant with ATM FORUM af-phy-0034 (E3 public UNI) and af-phy-0054 (DS3 public UNI). Easily Interfaced to ATM framer ICs such as PMC 7...

430310001

Vendor:MOLEXD/C:06+

43031-0001

Vendor:molexD/C:08+

Gain-Bandwidth Product (G +5) Gain Peaking 0.1dB Gain Flatness Bandwidth Large Signal Bandwidth Step Response: Slew Rate Rise/Fall Time Settling Time: 0.05% Spurious Free Dynamic Range Differential Gain Differential Phase Input Noise: Voltage Noise Density Current Noise Density

43031-0004

Vendor:MOLEX

An on-chip RF oscillator is enabled if OSCEN = 'High', and its output signal is added to the current output.The oscillator amplitude is set by an external resistor from RS to GND. Its frequency is set by an external resistor RF to GND. The oscillator signal is summed with the programmed Write and Read levels before amplification to the output. The oscillator signal has zero DC level and +I_pk to -I_pk signal ...

43031-0004

Vendor:MOLEX

An on-chip RF oscillator is enabled if OSCEN = 'High', and its output signal is added to the current output.The oscillator amplitude is set by an external resistor from RS to GND. Its frequency is set by an external resistor RF to GND. The oscillator signal is summed with the programmed Write and Read levels before amplification to the output. The oscillator signal has zero DC level and +I_pk to -I_pk signal ...

43031-0011

Vendor:MolexD/C:08+

• 3.3V, 5V, 12V, and adjustable output versions • Adjustable version output 1.23V to 37V 4% max. over line and load conditions. • Guaranteed 0.5A output current • Wide input voltage, up to 40V • Thermal shutdown and current limit protection • Requires only 4 external components. • Shutdown capability (standby mode) • Low power standby mode < 200&mi...

43045-0209

Vendor:MolexD/C:08+

The RF5189 requires only a single positive supply of 3.0V nominal (or greater) to operate to full specifications. Power control is provided through two bias control input pins (VREG1 and VREG2), but in most applications these are tied together and used as a single control input.

430450212

Vendor:MolexPackage Cooled:D/SD/C:07+

CAUTION: These devices are sensitive to electrostatic discharge. Follow proper ESD Handling Procedures. UltraFET™ is a trademark of Intersil Corporation. PSPICE™ is a registered trademark of MicroSim Corporation. SABER© is a Copyright of Analogy Inc. 1-888-INTERSIL or 407-727-9207 | Copyright © Intersil Corporation 1999.

430450212

Vendor:MolexPackage Cooled:D/SD/C:07+

CAUTION: These devices are sensitive to electrostatic discharge. Follow proper ESD Handling Procedures. UltraFET™ is a trademark of Intersil Corporation. PSPICE™ is a registered trademark of MicroSim Corporation. SABER© is a Copyright of Analogy Inc. 1-888-INTERSIL or 407-727-9207 | Copyright © Intersil Corporation 1999.

43045-0225

Vendor:MolexD/C:08+

43045-0400

Vendor:MOLEXD/C:07+

The TC51WHM616AXBN is a 67,108,864-bit pseudo static random access memory(PSRAM) organized as 4,194,304 words by 16 bits. Using Toshibas CMOS technology and advanced circuit techniques, it provides high density, high speed and low power. The device operates single power supply. The device also features SRAM-like W/R timing whereby the device is controlled by CE1 , OE , and WE on asynchronous. The device has...

43045-0409

Vendor:MolexD/C:08+

The PCI-Express differential clock outputs of the ICS557-03 are open source drivers and require an external series resistor and a resistor to ground. These resistor values and their allowable locations are shown in detail in the PCI-Express Layout Guidelines section.

43045-0411

Vendor:MOLEXD/C:07+

The signal conditioner demodulates the amplifier output signal and converts it to a binary signal. It compares the carrier signal with the 50% reference level (see Ref1 in Figure 5) and delivers a logical 1, if the carrier signal stays below the reference and a logical 0, if it exceeds the reference level. A smoothing filter suppress the space between the half-waves as well as a few missing periods in the...

43045-0412

Vendor:MOLEXD/C:07+

C Stand-alone MP3 Decoder C 48, 44.1, 32, 24, 22.05, 16 kHz Sampling Frequency C Separated Digital Volume Control on Left and Right Channels (Software Control using 31 Steps) C Bass, Medium, and Treble Control (31 Steps) C Bass Boost Sound Effect C Ancillary Data Extraction C CRC Error and MPEG Frame Synchronization Indicators Programmable Audio Output for Interfacing with Common Audio DAC C P...

43045-0420

Vendor:MOLEXD/C:07+

The optional 16K bytes boot block section includes a repro- gramming write lockout feature to provide data integrity. The boot sector is designed to contain user-secure code, and when the feature is enabled, the boot sector is perma- nently protected from being reprogrammed.

43045-0425

Vendor:MolexD/C:08+

43045-0600

Vendor:MOLEXD/C:07+

Low−Power Schottky TTL Load Over the Rated Temperature Range • Double Diode Protection on All Inputs • Pin−for−Pin Replacements for Corresponding CD4000 Series UB Suffix Devices • Pb−Free Packages are Available*

43045-0600

Vendor:MOLEXD/C:07+

Low−Power Schottky TTL Load Over the Rated Temperature Range • Double Diode Protection on All Inputs • Pin−for−Pin Replacements for Corresponding CD4000 Series UB Suffix Devices • Pb−Free Packages are Available*

43045-0607

Vendor:MolexD/C:08+

43045-0612

Vendor:MOLEXD/C:07+

Parameter Supply Voltage VDD to Ground Data Input, Data Output, VB Column Input Voltage, VCOL Free Air Operating Temperature Range, TA Storage Temperature Range, Ts Maximum Allowable Package Power Dissipation, PD[2,3] at TA = 71C Through-the-Wave Solder Temperature 1.59 mm (0.063") Below Body ESD Protection @ 1.5 kΩ, 100 pF

43045-0612

Vendor:MOLEXD/C:07+

Parameter Supply Voltage VDD to Ground Data Input, Data Output, VB Column Input Voltage, VCOL Free Air Operating Temperature Range, TA Storage Temperature Range, Ts Maximum Allowable Package Power Dissipation, PD[2,3] at TA = 71C Through-the-Wave Solder Temperature 1.59 mm (0.063") Below Body ESD Protection @ 1.5 kΩ, 100 pF

43045-0800

Vendor:MOLEXD/C:07+

When VCC is between 0 and 1.5 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by the current-sourcing capability of the driver.

43045-0800

Vendor:MOLEXD/C:07+

When VCC is between 0 and 1.5 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by the current-sourcing capability of the driver.

43045-0809

Vendor:MolexD/C:08+

(1) Electrical characteristics for "L" suffix devices are identical to their corresponding "non-L" suffix devices. (2) Derate linearly 5.71 mW/C for TA > +25C. (3) Derate linearly 3.08 mW/C for TA > +25C, 2N3501UB.

43045-0824

Vendor:MolexD/C:08+

43045-1012-1012

43045-1014

Vendor:MOLEXD/C:07+

Input to configure for DDR-ONLY mode or STANDARD SDRAM mode. 1 = DDR-ONLY mode. 0 = STANDARD SDRAM mode. When SEL_DDR is pulled HIGH or configured for DDR-ONLY mode, all the buffers will be configured as DDR outputs. Connect VDD3.3_2.5 to a 2.5V power supply in DDR-ONLY mode. When SEL_DDR is pulled LOW or configured for STANDARD SDRAM output, all the buffers will be configured as STANDARD SDRAM outputs. Co...

430451018

43045-1200

Vendor:MOLEXD/C:07+

Not 100% tested. CB = total capacitance of one bus line in pF. As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions. The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs which provide improved noise spike suppression. This eli...

430451212

Vendor:MLXPackage Cooled:5,400

Unless otherwise specified, the following specifications apply for VSSA = VSSIO = 0V, VDDA = +3.0V, VDDIO = +2.5V, VIN = 2 VP-P, STBY = 0V, VREF = 1.20V, (External Supply) fCLK = 80 MHz, 50% Duty Cycle, CL = 10 pF/pin. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25˚C.

430451212

Vendor:MLXPackage Cooled:5,400

Unless otherwise specified, the following specifications apply for VSSA = VSSIO = 0V, VDDA = +3.0V, VDDIO = +2.5V, VIN = 2 VP-P, STBY = 0V, VREF = 1.20V, (External Supply) fCLK = 80 MHz, 50% Duty Cycle, CL = 10 pF/pin. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25˚C.

43045-1212

Vendor:MOLEXD/C:07+

† Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE: All voltage va...

43045-1614

Vendor:MOLEXD/C:07+

The 43045-1614 Development Kit contains access sys- tem software which must be linked with the application software in order to complete integration. The support for the application development environments and operating systems lies in the interface software of the access system. The access system contains the low level interface for communicating with the Buttons.

430451616

43045-1625

Vendor:MolexD/C:08+