T026NSR

Vendor:TIPackage Cooled:SOP-8D/C:04+

The DS1267 Dual Digital Potentiometer Chip consists of two digitally controlled, solid-state potentiometers. Each potentiometer is composed of 256 resistive sections. Between each resistive section and both ends of the potentiometer are tap points which are accessible to the wiper. The position of the wiper on the resistive array is set by an 8-bit value that controls which tap point is connected to the wipe...

T02AA174

The LH543601 has two 36-bit ports, Port A and Port B. Each port has its own port-synchronous clock, but the two ports may operate asynchronously relative to each other. Data flow is initiated at a port by the rising edge of the appropriate clock; it is gated by the corresponding edge- sampled enable, request, and read/write control signals. At the maximum operating frequency, the clock duty cycle may...

T02SF

D/C:N/A

The HS-80C85RH is an 8-bit CMOS microprocessor fabricated using the Intersil radiation hardened self-aligned junction isolated (SAJI) silicon gate technology. Latch-up free operation is achieved by the use of epitaxial starting material to eliminate the parasitic SCR effect seen in conventional bulk CMOS devices.

T03011

Vendor:ZETEXPackage Cooled:SMDD/C:07+

T0309S

Vendor:INNETD/C:9906+

Cntrl (Bump A1): Shutdown control pin. When VCntrl is 1.4V, the LM3502 is enabled or ON. When VCntrl is 0.3V, the LM3502 will enter into shutdown mode operation. The LM3502 has an internal pull down resistor on the Cntrl pin, thus the device is normally in the off state or shutdown mode of operation.

T034PWR

Vendor:TIPackage Cooled:TSSOP16D/C:04+

2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents...

T0384JS

Vendor:TRUMPIONPackage Cooled:O305D/C:0252+

• Support for low voltage interface to VGA controller • Universal digital interface accepts YCrCb (CCIR656) or RGB (15, 16 or 24-bit multiplexed) video data in both non-interlaced and interlaced formats • TrueScale TM rendering engine supports underscan operations for various graphic resolutions† ¥ • Enhanced text sharpness and adaptive flicker removal with up to 5...

T0392

Vendor:INNETD/C:01+

This device operates from a single 3.3-V supply. The device has integrated 100-Ω line termination and provides self-biasing. The input tolerates most differential signaling levels such as LVDS, LVPECL or CML. The output impedance matches 100-Ω line impedance. The inputs and outputs may be ac coupled for best interconnectivity with other devices such as SERDES I/O or additional XAUI multiplexer...

T0393

Vendor:INNETD/C:01+

The 512Mb DDR2 SDRAM is organized as a 32Mbit x 4 I/Os x 4 banks, 16Mbit x 8 I/Os x 4banks or 8Mbit x 16 I/Os x 4 banks device. This synchronous device achieves high speed double- data-rate transfer rates of up to 533Mb/sec/pin (DDR2-533) for general applications. The chip is designed to comply with the following key DDR2 SDRAM features such as posted CAS with additive latency, write latency = read latency -...

T0409DG

Vendor:TAGD/C:08+

T044EJ89

T04-560

T0505BH

Vendor:STPackage Cooled:8000D/C:07+

T0505DH

Vendor:STPackage Cooled:8000D/C:07+

Sensitivity describes the gain of the sensor and can be determined by applying 1g acceleration to it. As the sensor can measure DC accelerations this can be done easily by pointing the axis of interest towards the center of the earth, note the output value, rotate the sensor by 180 degrees (point to the sky) and note the output value again thus applying 1g acceleration to the sensor. Subtracting the larger...

T0505NH

Vendor:STPackage Cooled:TO-220D/C:01+

• Ultra-miniature size with universal terminal footprint • High contact capacity: 10 A • Class B coil insulation type available • TV-5 type available 1 Form A type TV-5 1 Form C type TV-5 (N.O. side only) • VDE, TÜV also approved • Sealed construction for automatic cleaning

T0505NH

Vendor:STPackage Cooled:8000D/C:01+

• Ultra-miniature size with universal terminal footprint • High contact capacity: 10 A • Class B coil insulation type available • TV-5 type available 1 Form A type TV-5 1 Form C type TV-5 (N.O. side only) • VDE, TÜV also approved • Sealed construction for automatic cleaning

T0509BH

Vendor:STPackage Cooled:TO-D/C:07+

T0509BH

Vendor:STPackage Cooled:TO-D/C:07+

T0509DH

Vendor:STPackage Cooled:TO220D/C:07+

FUNCTION The M63800FP has seven circuits, which are made of input inverters and current-sourcing outputs. The outputs are made of PNP transistors and NPN Darlington transistors. The PNP transistor base current is constant. A spike-killer clamping diode is provided between each output pin and GND. VS (pin 8) and GND (pin 9) are used commonly among the eight circuits. The input has resistance of 3k...

T0509DH

Vendor:STPackage Cooled:TO220D/C:07+

FUNCTION The M63800FP has seven circuits, which are made of input inverters and current-sourcing outputs. The outputs are made of PNP transistors and NPN Darlington transistors. The PNP transistor base current is constant. A spike-killer clamping diode is provided between each output pin and GND. VS (pin 8) and GND (pin 9) are used commonly among the eight circuits. The input has resistance of 3k...

T0509MH

Vendor:STPackage Cooled:TO-D/C:07+

T0509MH

Vendor:STPackage Cooled:TO-D/C:07+

T0509NH

Vendor:STPackage Cooled:TO-D/C:07+

T0509NH

Vendor:STPackage Cooled:TO-D/C:07+

T0510BH

Vendor:STPackage Cooled:TO-D/C:07+

T0510DH

Vendor:STPackage Cooled:TO-D/C:07+

T0510DH

Vendor:STPackage Cooled:TO-D/C:07+

T0510MH

Vendor:STPackage Cooled:8000D/C:07+

NOTES: 1. The ICC current listed includes both the DC operating current and the frequency dependent component (@ 5 MHz). The frequency component typically is less than 2 mA/MHz, with OE at VIH. 2. ICC active while Embedded Algorithm (program or erase) is in progress. 3. DC test conditions: VIL = 0.3V, VIH = VCC - 0.3V

T0510NH

Vendor:STPackage Cooled:TO-D/C:07+

T0512BH

Vendor:STPackage Cooled:TO-D/C:07+

T0512DH

Vendor:STPackage Cooled:8000D/C:07+

T0512MH

Vendor:STPackage Cooled:8000D/C:07+

T0512NH

Vendor:STPackage Cooled:TO-D/C:07+

T0512NH

Vendor:STPackage Cooled:TO-D/C:07+

T052A

Vendor:TIPackage Cooled:SOP-8P

Requires few external parts Low distortion (total harmonic distortion = 0.01% at 3 W) Low noise (at Rg = 620 Ω, noise is 0.15 mV (muting off) or 0.1 mV (muting on)) Popping noise minimized Highly reliable current-limiting ASO protector keeps speakers safe from all kinds of trouble. Reliability is further enhanced by a fast-acting thermal shutdown protection circuit with on/off hysteresis.

T052NSR

Vendor:TIPackage Cooled:SOP-8D/C:07+

The ground return for the digital supply for the T052NSRs output drivers. This pin should be connected to the system digital ground, but not be connected in close proximity to the T052NSRs DGND or AGND pins. See Section 5.0 (Layout and Grounding) for more details.

T056114641

Vendor:[H]Package Cooled:N/AD/C:9+

T05UD405

D/C:06+

Complete USB Hub Power Solution Meets USB Specifications 1.1 and 2.0 Independent Thermal and Short-Circuit Protection 3.3-V Regulator for USB Hub Controller Overcurrent Logic Outputs 4.5-V to 5.5-V Operating Range CMOS- and TTL-Compatible Enable Inputs 185 µA Bus-Power Supply Current Available in 24-Pin SSOP Package C40C to 85C Ambient Temperature Range

T0600

Package Cooled:BGA0505D/C:02+

Each of the three codewheel materials offers a certain advantage. Metal codewheels are the most versatile, with a tem- perature rating up to 100C, resolution to 512 CPR (28 mm diameter), as well as 2 and 3 channel outputs. Film codewheels offer higher resolution (up to 1024 CPR on a 28 mm diameter) with an operating temperature of 70C. Glass codewheels combine the best of film and metal, of...

T0605BH

Vendor:STPackage Cooled:8000D/C:07+

T0605BH

Vendor:STPackage Cooled:TO-D/C:07+

T0605DH

Vendor:STPackage Cooled:8000D/C:07+

. . . employing the Schottky Barrier principle in a large area metal-to-silicon power diode. State-of-the-art geometry features epitaxial construction with oxide passivation and metal overlap contact. Ideally suited for use as rectifiers in low- voltage, high- frequency inverters, free wheeling diodes, and polarity protection diodes.

T0605DH

Vendor:STPackage Cooled:8000D/C:07+

. . . employing the Schottky Barrier principle in a large area metal-to-silicon power diode. State-of-the-art geometry features epitaxial construction with oxide passivation and metal overlap contact. Ideally suited for use as rectifiers in low- voltage, high- frequency inverters, free wheeling diodes, and polarity protection diodes.

T0605MH

Vendor:STPackage Cooled:8000D/C:01+

Notes: a. Signals on SX, DX, or INX exceeding V+ or V− will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads welded or soldered to PC Board. c. Derate 6 mW/_C above 75_C d. Derate 12 mW/_C above 25_C

T0605NH

Vendor:STPackage Cooled:8000D/C:01+

The Hyundai HYM71V631601 H-Series are 16Mx64bits Synchronous DRAM Modules. The modules are composed of eight 16Mx8bit CMOS Synchronous DRAMs in 400mil 54pin TSOP-II package, one 2Kbit EEPROM in 8pin TSSOP package on a 168pin glass-epoxy printed circuit board. One 0.22uF and one 0.0022uF decoupling capacitors per each SDRAM are mounted on the PCB.

T0608DJ

California Micro Devices's CM1406 is an EMI filter array with ESD protection, which integrates 4 pi filters (C-R-C). The CM1406 has component values of 15pF- 200Ω-15pF. The parts include ESD protection diodes on every pin, which provide a very high level of protec- tion for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The ESD diodes connected to the fi...

T0609BH

Vendor:STPackage Cooled:TO-D/C:07+

T0609DH

Vendor:STPackage Cooled:TO-D/C:07+

IC Test Pin 4Fsc X - tal Input For PAL (17.73447MHz) 4Fsc X - tal Output For PAL Ground X - tal Ground PAL/NTSC Mode Select ion Pin 760H/510H CCD Mode Selection Pin IC Reset Input I/O Power Supply Phase Comparator Output Of PAL PLL Ground (INTRENAL) DCP Chip Select Pin (Low Active) Wait For Micom Interface (Low Active)

T0609MH

Vendor:STPackage Cooled:TO-D/C:07+

T0609MH

Vendor:STPackage Cooled:TO-D/C:07+

T0609NH

Vendor:STPackage Cooled:TO-220D/C:01+

The T0609NH and T0609NH power distribution switches are intended for applications where heavy capacitive loads and short circuits are likely to be encountered. The T0609NH and the T0609NH are 135-mΩ N-channel MOSFET high-side power switches. Each switch is controlled by a logic enable compatible with 5-V and 3-V logic. Gate drive is provided by an internal charge pump that controls the power-switch ...

T060B

Vendor:3D/C:N/A

The Intersil family of Star*Power FETs includes a series of devices in various voltage, current and package styles. The portfolio consists of Star*Power and Star*Power Gold products. Star*Power FETs are optimized for total dose and rDS(ON) while exhibiting SEE capability at full rated voltage up to an LET of 37. Star*Power Gold FETs have been optimized for SEE and Gate Charge combining SEE performance...

T0610BH

Vendor:STPackage Cooled:TO-220D/C:01+

The DS1554 is in the write mode whenever WE and CE are in their active state. The start of a write is referenced to the latter occurring transition of WE or CE . The addresses must be held valid throughout the cycle. CE and WE must return inactive for a minimum of tWR prior to the initiation of a subsequent read or write cycle. Data in must be valid tDS prior to the end of the write and remain va...

T0610BJ

Vendor:STPackage Cooled:TO-D/C:07+

T0610BJ

Vendor:STPackage Cooled:TO-D/C:07+

T0610DH

Vendor:STPackage Cooled:TO-D/C:07+

T0610MH

Vendor:STPackage Cooled:8000D/C:07+

† Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The voltage ...

T0610MH

Vendor:STPackage Cooled:TO-D/C:07+

† Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The voltage ...

T0610MJ

Vendor:5050Package Cooled:STD/C:TO-220

T0610NH

Vendor:STPackage Cooled:8000D/C:01+

PMD assumes no liability for applications assistance or customer product design. PMD does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of PMD covering or relating to any combination, machine, or process in which such products or services might be or are used. PMD's publication of info...

T0610NJ

Vendor:STPackage Cooled:8000D/C:07+

T0612BH

Vendor:6000Package Cooled:STD/C:TO-220

T0612BJ

Vendor:STPackage Cooled:8000D/C:07+

T0612MJ

Vendor:5000Package Cooled:TO-220D/C:TO-220

T0612NH

Vendor:STPackage Cooled:TO-220D/C:TO-220

T0612NJ

Vendor:STPackage Cooled:TO-D/C:07+

T0612NJ

Vendor:STPackage Cooled:8000D/C:07+

T061C

Vendor:ONSPackage Cooled:SOP8

Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func- tional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guar- antee specific performance limits. This assumes that the device is within th...

T0620

Vendor:ATMELPackage Cooled:SSOP16

T062A

Package Cooled:SOP8

• Plastic package has Underwriters Laboratories Flammability Classification 94V-0 • Ideally suited for freewheeling diode and power factor correction applications • Low leakage • Superfast recovery time for high efficiency • Ideal for diode modulation and secondary DC/DC output rectification • Glass passivated chip junction

T064PWR

Vendor:TIPackage Cooled:TSSOP16D/C:04+

3. When operating the ADS-929 from 12V supplies, do not drive external circuitry with the REFERENCE OUTPUT. The reference's accuracy and drift specifications may not be met, and loading the circuit may cause accuracy errors within the converter.

T065BE0

T0686-1

Vendor:CPClarePackage Cooled:ZIPD/C:1997

T0686-2

Vendor:CPClarePackage Cooled:ZIPD/C:1997

The SD1010A also provides distinguished system features to the TFT LCD monitor solution. The first one is plug-and-play, and the second one is cost-effective system solution. To be truly plug-and-display, the SD1010A performs automatic input mode detection and auto phase calibration, so the LCD monitor can ensure that the A/D converters sample clock is precisely synchronized with the input video data, and to...

T06CAB

Vendor:N/APackage Cooled:513

T06CAD(TMP06)

Vendor:BROADCOMPackage Cooled:TSOP8D/C:——

T07109K

HIGH SPEED: tPD = 13ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 138

T071C

Vendor:ONSPackage Cooled:SOP8

For high-density packaging applications, the UCN5818EPF is furnished in a 44-lead plastic chip carrier (quad pack) for surface mounting on solder lands with 0.050" (1.27 mm) centers. The PLCC allows -25 mA continuous operation of all outputs simultaneously at ambient temperatures to 60C. Similar devices are available as the UCN5810AF/LWF (10 bits), UCN5811A (12 bits), and UCN5812AF/EPF (20 bits).

T074PWR

Vendor:TIPackage Cooled:TSSOP16D/C:04+

Very Low Power Consumption . . . 2 mW Typ at VDD = 5 V Capable of Operation in Astable Mode CMOS Output Capable of Swinging Rail to Rail High Output-Current Capability Sink 100 mA Typ Source 10 mA Typ Output Fully Compatible With CMOS, TTL, and MOS Low Supply Current Reduces Spikes During Output Transitions Single-Supply Operation From 2 V to 15 V Functionally interchangeable With the NE556; Has Same ...

T074PWR

Vendor:TIPackage Cooled:TSSOP16D/C:04+

Very Low Power Consumption . . . 2 mW Typ at VDD = 5 V Capable of Operation in Astable Mode CMOS Output Capable of Swinging Rail to Rail High Output-Current Capability Sink 100 mA Typ Source 10 mA Typ Output Fully Compatible With CMOS, TTL, and MOS Low Supply Current Reduces Spikes During Output Transitions Single-Supply Operation From 2 V to 15 V Functionally interchangeable With the NE556; Has Same ...

T07906CP

Vendor:atmelPackage Cooled:atmelD/C:dc0404

All parameters, unless otherwise specified, are measured at ambient temperature 20ºC. Custom-made services available with operational quantity. Please let us know your special requirements. Specifications subject to change without prior notice.

T07CAB

Vendor:BROADCOMPackage Cooled:57

T0800PJQ

Vendor:atmelPackage Cooled:atmelD/C:dc0349

128 Kbytes Backwardly compatible with SAB 8051 Functionally compatible with SAB 80515 Idle and power-down mode Plastic leaded chip carrier package: P-LCC-68 Plastic Metric Quad Flat Package P-MQFP-80 Two temperature ranges available: 0 to 70 ˚C(for 12, 16, 20 MHz) C 40 to 85 ˚C (for 12, 16 MHz)

T0802

Vendor:TEMICPackage Cooled:SSOP-16PD/C:03+

The I/O and logic functions of the FPGA and their associ- ated interconnections are established by a configuration program. The program is loaded either automatically upon power up, or on command, depending on the state of the three FPGA mode pins. In Master Mode, the FPGA auto- matically loads the configuration program from an external memory. The Serial Configuration EEPROM has been designed for co...

T0802

Vendor:TEMICPackage Cooled:SSOP-16PD/C:03+

The I/O and logic functions of the FPGA and their associ- ated interconnections are established by a configuration program. The program is loaded either automatically upon power up, or on command, depending on the state of the three FPGA mode pins. In Master Mode, the FPGA auto- matically loads the configuration program from an external memory. The Serial Configuration EEPROM has been designed for co...

T0805BH

Vendor:STPackage Cooled:TO-D/C:07+

T0805BH

Vendor:STPackage Cooled:8000D/C:07+

T0805DH

Vendor:STPackage Cooled:TO-D/C:07+

An output enable (OE) pin is provided to three-state the Q0C8 outputs when OE is asserted. When OE is enabled (LOW), data in the output register will be available to the Q0C8 outputs after tOE. If devices are cascaded, the OE function will only output data on the FIFO that is read enabled.

T0805MH

Vendor:STPackage Cooled:TO-220D/C:01+

6. TUNE/SEEK/ATP (AUTO TUNING PRESET) CONTROL This button performs two functions: Auto Tuning Preset Scan and Auto Tuning Preset Memory. This function allows you to locate and store up to six stations in the selected band automatically. Select the desired band, then rotate the knob counterclockwise to select a station on a lower frequency or clockwise to select a station on a higher frequency. Hold the ...

T0805MH

Vendor:STPackage Cooled:TO-220D/C:01+

6. TUNE/SEEK/ATP (AUTO TUNING PRESET) CONTROL This button performs two functions: Auto Tuning Preset Scan and Auto Tuning Preset Memory. This function allows you to locate and store up to six stations in the selected band automatically. Select the desired band, then rotate the knob counterclockwise to select a station on a lower frequency or clockwise to select a station on a higher frequency. Hold the ...

T0805NH

Vendor:STPackage Cooled:TO-220D/C:01+

This document contains proprietary and confidential information of Performance Motion Devices, Inc., and is protected by federal copyright law. The contents of this document may not be disclosed to third parties, translated, copied, or duplicated in any form, in whole or in part, without the express written permission of PMD. The information contained in this document is subject to change without notice. No...

T0805R474KCT

Vendor:N/APackage Cooled:0805-474K

T0806-TCQ

Vendor:ATMELD/C:02+

NEC's T0806-TCQ-CC and T0806-TCQ-CC are 1550 nm Co- axial Module DFB (Distributed Feed-Back) laser diode with single mode fiber. Multiple Quantum Well (MQW) structure is adopted to achieve stable dynamic single longitudinal mode operation over a wide temperature range of -10 to +85C.

T0806TCQ19

Vendor:tfkPackage Cooled:tfkD/C:dc02

3.2 Manchester Encoder The Manchester encoder receives the NRZ data from the controller and converts it into Manchester format using the internal 20MHz clocks. TXD and TXE must be synchronized by TXC. The encoder also guarantees that a low transition occurs first at the start of the packet and appends the IDL at the end of the transmitted data.

T0806-TCQG

Vendor:ATMELPackage Cooled:16-SSOPD/C:05+

T0806-TQC

Vendor:2500Package Cooled:ATD/C:02+

T0809BH

Vendor:STPackage Cooled:8000D/C:07+

T0809DH

Vendor:STPackage Cooled:TO-D/C:07+

• SAW (Surface Acoustic Wave) IF filters • RSSI measurement components • IF amplifiers • Oscillator components • Package optimization enables low-cost 2-layer system PCB • Minimal in-house RF expertise required

T0809MH

Vendor:4500Package Cooled:STD/C:TO-220

T0809NH

Vendor:STPackage Cooled:TO-220D/C:01+

At time t3, the VGD supply has dropped below its lower threshold, but the output voltage is still above its thresh- old point. This results in an energy pulse to the gate drive supply at t4. However, while the gate drive is being serv- iced, the output voltage has dropped below its lower threshold, so the state machine commands an energy pulse to the output as soon as the gate drive pulse is completed.